Our Principals

 

We Represent

 
Expand All | Contact All

Power Quality Analyzer

PQM-702

    Description

    • » Measurements according to EN 50160
    • » Voltage L1, L2, L3, N-PE
      - average, minimum, maximum and instantaneous values, range to 760V, ability to work with voltage transformers,
    • » Current L1, L2, L3, N (four inputs)
      - average, minimum, maximum and instantaneous values, measurement current with range to 3 kA (depends on used clamp), ability to work with current transformers,
    • » Crest factor for voltage and current,
    • » Frequency from 40Hz to 70Hz ,
    • » Active, reactive, distortion, apparent power, including the type of reactive power (capacitive, inductive),
    • » Power recording:
      - Budeanu method,
      - IEEE 1459,
    • » Active, reactive, apparent energy,
    • » Power factor, cosφ, tgφ,
    • » K factor (transformer overload caused by the harmonics),
    • » Up to 50th harmonics for voltage and current,
    • » Total Harmonic Distortion (THD) for voltage and current,
    • » Short-term (PST) and long-term (PLT) flicker,
    • » Unbalance of voltage and current,
    • » Current events detection including waveforms recording,
    • » Current and voltage waveforms recording after each averaging period.

     The device is designed to work with networks:

    • » with nominal frequency 50/60Hz,
    • » with nominal voltage:
        64/110 V; 110/190 V; 115/200 V; 127/220 V; 220/380 V; 230/400 V; 240/415 V; 254/440 V; 290/500 V; 400/690 V,
    • » DC network

    Supported networks:

    • » single-phase,
    • » two-phase with common N conductor,
    • » three-phase star connection with and without N conductor,
    • » three-phase delta.

Specification

Specification Range Resolution Accuracy

AC
voltage
(TRMS)

- 0,0…760,0 V 0,01 % Un ±0,1% Un
Crest
Factor
Voltage

1,00…10,00
(≤1,65 for
voltage 690 V)

0,01 ±5%
Current 1,00…10,00
(≤3,6 Inom)
0,01 ± 5% m.v.
AC
current
TRMS
- depends on
the clamp*
0,01 % of nominal range ±0,1% of nominal
range
(add clamps
accuracy)
Frequency - 40,00...70,00 Hz 0,01Hz ±0,01 Hz
Active,
reactive,
apparent
power
and
distortion
- depends
of configuration
(transformers,
clamp)
up to 4
decimal places
depends
on configuration
(transformers,
clamp)
Active, reactive apparent energy - depends
of configuration
(transformers,
clamp)
up to 4
decimal places
the same
as above
cosφ
and Power
Factor (PF)
- 0,00...1,00 0,01 ±0,03
tgφ - 0,00...10,00 0,01 depends on Active
and Reactive
power accuracy
Harmonics Voltage same as for AC
voltage TRMS
same as for
AC voltage TRMS
±5% Uh
for Uh ≥ 1% Un
±0,05% Un
for Uh < 1% Un
 
Current same as for AC
current TRMS
same as for
AC current TRMS
± 5% Ih 
for Ih ≥ 3% In
± 0,15% In
for Ih < 3% In
Total
Harmonics
Distortion
Voltage 0,0..100,0% 0,1% ±5%
Current ±5%
Harmonics
active
and
reactive
power
- depends on configuration
(transformers,
clamp)
depends
on current
and voltage
minimum value
-

Angle
between
voltage
and current
harmonics

- -180,0…+180,0o 0,1o ±(h x 1o)
K-Factor - 1,0...50,0 0,1 ±10%
Flicker - 0,20...10,00 0,01 ±5%
Unbalance Voltage and Current 0,0...20,0% 0,1% ±0,15%
(absolute error)

*Clamp F-1/F-2/F-3:0..3000 A (10000 Ap-p) *Clamp C-4: 0..1000 A (3600 Ap-p)*Clamp C-5: 0..1000 A (3600 Ap-p)*Clamp C-6: 0..10 A (36 Ap-p) (without current transformers) *Clamp C-7: 0...100 A (360 Ap-p )



PQM-701

    Description

  • ANALYZER MEASURES AND RECORDS ACCORDING TO THE EN 61000 - 4-30 CLASS-A STANDARD The device is designed to work with networks with nominal frequency 50/60 Hz. The device is designed to work with networks with nominal voltage:
  • » 110/190 V,
  • » 115/200 V,
  • » 220/380 V,
  • » 230/400 V,
  • » 240/415 V,
  • » 400/690 V.

  • The network configuration is set from the computer software.
    Supported networks:
  • » single-phase,
  • » two-phase with the common N,
  • » three-phase star with and without N,
  • » three-phase triangle.
  • Specification

    Possible measurements:

    • » Measurements according to EN 50160
    • » Voltage L1, L2, L3, N-PE (five inputs, compiles with EN 61000 - 4-30, class A)
      - average, minimum, maximum and instantaneous values, range to 690 V, ability to work with voltage transformers,
    • » Current L1, L2, L3, N (four inputs)
      - average, minimum, maximum and instantaneous values, measurement current with range to 3 kA (depends on used clamp), ability to work with current transformers,
    • » Crest factor for voltage and current,
    • » Frequency from 40 Hz to 70 Hz (compiles with EN 61000 - 4-30, class A),
    • » Active, reactive, distortion, apparent power, including the type of reactive power (capacitive, inductive),
    • » Power recording:
      - Budeanu method,
      - IEEE 1459,
    • » Active, reactive, apparent energy,
    • » Power factor, cosφ, tgφ,
    • » K factor (transformer overload caused by the harmonics),
    • » Up to 50th harmonics for voltage and current (compiles with EN 61000 - 4-7, class I),
    • » Total Harmonic Distortion (THD) for voltage and current,
    • » Short-term (PST) and long-term (PLT) flicker (compiles with EN 61000 - 4-15, class A),
    • » Unballace of Voltage (compiles with EN 61000 - 4-30, class A) and current,
    • » Voltage dips, swells and interruption registration including oscillograms (compiles with EN 61000 - 4-30, class A),
    • » Current events registration including oscillograms,
    • » Current and voltage oscillograms registration after each averaging period.
    Specification Range Resolution Accuracy

    AC
    voltage
    (TRMS)

    - 0,0…690,0 V 0,01 % Un ±0,1% Un
    Crest
    Factor
    Voltage

    1,00…10,00
    (≤1,65 for
    voltage 690 V)

    0,01 ±5%
    Current 1,00…10,00
    (≤3,6 Inom)
    0,01 ± 5% m.v.
    AC
    current
    TRMS
    - depends on
    the clamp*
    0,01 % of nominal range ±0,1% of nominal
    range
    (add clamps
    accuracy)
    Frequency - 40,00...70,00 Hz 0,01 Hz ±0,01 Hz
    Active,
    reactive,
    apparent
    power
    and
    distortion
    - depends
    of configuration
    (transformers,
    clamp)
    up to 4
    decimal places
    depends
    on configuration
    (transformers,
    clamp)
    Active, reactive apparent energy - depends
    of configuration
    (transformers,
    clamp)
    up to 4
    decimal places
    the same
    as above
    cosφ
    and Power
    Factor (PF)
    - 0,00...1,00 0,01 ±0,03
    tgφ - 0,00...10,00 0,01 depends on Active
    and Reactive
    power accuracy
    Harmonics Voltage same as for AC
    voltage TRMS
    same as for
    AC voltage TRMS
    ±5% Uh
    for Uh ≥ 1% Un
    ±0,05% Un
    for Uh < 1% Un
     
    Current same as for AC
    current TRMS
    same as for
    AC current TRMS
    ± 5% Ih 
    for Ih ≥ 3% In
    ± 0,15% In
    for Ih < 3% In
    Total
    Harmonics
    Distortion
    Voltage 0,0..100,0% 0,1% ±5%
    Current ±5%
    Harmonics
    active
    and
    reactive
    power
    - depends on configuration
    (transformers,
    clamp)
    depends
    on current
    and voltage
    minimum value
    -

    Angle
    between
    voltage
    and current
    harmonics

    - -180,0…+180,0o 0,1o ±(h x 1o)
    K-Factor - 1,0...50,0 0,1 ±10%
    Flicker - 0,20...10,00 0,01 ±5%
    Unbalance Voltage and Current 0,0...20,0% 0,1% ±0,15%
    (absolute error)

    *Clamp F-1/F-2/F-3:0..3000 A (10000 Ap-p) *Clamp C-4: 0..1000 A (3600 Ap-p)*Clamp C-5: 0..1000 A (3600 Ap-p)*Clamp C-6: 0..10 A (36 Ap-p) (without current transformers)

    Sonel Analysis 1.0

    „SONEL Analysis” software is an application used to work with PQM-701 power quality analyzer. It enables:

    • » analyzer configuration,
    • » reading data from the analyzer,
    • » network parameters check in real time,
    • » data deleting in the analyzer,
    • » data presentation in tables,
    • » data presentation in diagrams,
    • » data analysis according to EN 50160 or according to user defined conditions,
    • » independent service of multiple analyzers,
    • » software upgrade through the Internet.

    Analyzer configuration

    The software enables configuration of all analyzer’s parameters. The configuraton is made on the PC computer and later transfered to the analyzer. The configuration settings can be stored on hard drive or other data storage devices to be used later.The software enables the configuration of:

    • » wthe choice of Measurement Points and memory assigment to each Measurement Point,
    • » analyzer time settings,
    • » keyboard lock,
    • » PIN code security,
    • » averaging time setting,
    • » choice of current and voltage transformers,
    • » trigger mode choice (immidiately, after an event or according to the scheduler),
    • » choice of clamp’s type, setting of additional parameters registration in N and PE channels,
    • » choice of network type, for which the analyzer will be used.

    The analyzer has four independent Measurement Points. Each Measurement Point can be set individually to perform four different types of registration without need to change analyzer’s configuration.

    For each Measurement Point the following settings can be made:

    • » cwheather the analyzer shall work according to EN 50160 or according to user defined conditions,
    • » for each registration user can define, which network parameters shall be registered,
    • » for each parameter user can define wheather the analyzer shall register average, minimum, maximum or instantaneous values,
    • » the limits beyond which the analyzer will record the event can be defined.

    Recent data reading

    “SONEL Analysis” software enables reading of selected parameters and their graphic presentation in real time.These parameters are measured independently of the registration saved on the memory card. User can check:

    • » wvoltage and current diagrams (oscilloscope),
    • » diagrams of voltage and current in time function,
    • » scope phasor,
    • » different parameters values,
    • » harmonics and harmonics’ power.

     

    Data analysis

    With “SONEL Analysis” software user can read data stored on the memory card and analyze them. Data from the analyzer can be stored on hard drive and be used later. This feature enables data archiving.

    The user can analyze the data from the device.There is a choice of:

    • General – all data are shown with dots (Measurements, Events and Oscillograms),
    • Measurements – all measured values registered in averaging time are shown with dots (voltage, frequency, etc.),
    • Events – all detected events are shown with dots (dips, swells, interruptions, etc.).


PQM-701Z

    Description

  • ANALYZER MEASURES AND RECORDS ACCORDING TO THE EN 61000 - 4-30 CLASS-A STANDARD The device is designed to work with networks with nominal frequency 50/60 Hz. The device is designed to work with networks with nominal voltage:
  • » 110/190 V,
  • » 115/200 V,
  • » 220/380 V,
  • » 230/400 V,
  • » 240/415 V,
  • » 400/690 V.

  • The network configuration is set from the computer software.
    Supported networks:
  • » single-phase,
  • » two-phase with the common N,
  • » three-phase star with and without N,
  • » three-phase triangle.
  • Specification

    Possible measurements:

    • » Measurements according to EN 50160
    • » Voltage L1, L2, L3, N-PE (five inputs, compiles with EN 61000 - 4-30, class A)
      - average, minimum, maximum and instantaneous values, range to 690 V, ability to work with voltage transformers,
    • » Current L1, L2, L3, N (four inputs)
      - average, minimum, maximum and instantaneous values, measurement current with range to 3 kA (depends on used clamp), ability to work with current transformers,
    • » Crest factor for voltage and current,
    • » Frequency from 40 Hz to 70 Hz (compiles with EN 61000 - 4-30, class A),
    • » Active, reactive, distortion, apparent power, including the type of reactive power (capacitive, inductive),
    • » Power recording:
      - Budeanu method,
      - IEEE 1459,
    • » Active, reactive, apparent energy,
    • » Power factor, cosφ, tgφ,
    • » K factor (transformer overload caused by the harmonics),
    • » Up to 50th harmonics for voltage and current (compiles with EN 61000 - 4-7, class I),
    • » Total Harmonic Distortion (THD) for voltage and current,
    • » Short-term (PST) and long-term (PLT) flicker (compiles with EN 61000 - 4-15, class A),
    • » Unballace of Voltage (compiles with EN 61000 - 4-30, class A) and current,
    • » Voltage dips, swells and interruption registration including oscillograms (compiles with EN 61000 - 4-30, class A),
    • » Current events registration including oscillograms,
    • » Current and voltage oscillograms registration after each averaging period.
    Specification Range Resolution Accuracy

    AC
    voltage
    (TRMS)

    - 0,0…690,0 V 0,01 % Un ±0,1% Un
    Crest
    Factor
    Voltage

    1,00…10,00
    (≤1,65 for
    voltage 690 V)

    0,01 ±5%
    Current 1,00…10,00
    (≤3,6 Inom)
    0,01 ± 5% m.v.
    AC
    current
    TRMS
    - depends on
    the clamp*
    0,01 % of nominal range ±0,1% of nominal
    range
    (add clamps
    accuracy)
    Frequency - 40,00...70,00 Hz 0,01 Hz ±0,01 Hz
    Active,
    reactive,
    apparent
    power
    and
    distortion
    - depends
    of configuration
    (transformers,
    clamp)
    up to 4
    decimal places
    depends
    on configuration
    (transformers,
    clamp)
    Active, reactive apparent energy - depends
    of configuration
    (transformers,
    clamp)
    up to 4
    decimal places
    the same
    as above
    cosφ
    and Power
    Factor (PF)
    - 0,00...1,00 0,01 ±0,03
    tgφ - 0,00...10,00 0,01 depends on Active
    and Reactive
    power accuracy
    Harmonics Voltage same as for AC
    voltage TRMS
    same as for
    AC voltage TRMS
    ±5% Uh
    for Uh ≥ 1% Un
    ±0,05% Un
    for Uh < 1% Un
     
    Current same as for AC
    current TRMS
    same as for
    AC current TRMS
    ± 5% Ih 
    for Ih ≥ 3% In
    ± 0,15% In
    for Ih < 3% In
    Total
    Harmonics
    Distortion
    Voltage 0,0..100,0% 0,1% ±5%
    Current ±5%
    Harmonics
    active
    and
    reactive
    power
    - depends on configuration
    (transformers,
    clamp)
    depends
    on current
    and voltage
    minimum value
    -

    Angle
    between
    voltage
    and current
    harmonics

    - -180,0…+180,0o 0,1o ±(h x 1o)
    K-Factor - 1,0...50,0 0,1 ±10%
    Flicker - 0,20...10,00 0,01 ±5%
    Unbalance Voltage and Current 0,0...20,0% 0,1% ±0,15%
    (absolute error)

    *Clamp F-1/F-2/F-3:0..3000 A (10000 Ap-p) *Clamp C-4: 0..1000 A (3600 Ap-p)*Clamp C-5: 0..1000 A (3600 Ap-p)*Clamp C-6: 0..10 A (36 Ap-p) (without current transformers)

    Sonel Analysis 1.0

    „SONEL Analysis” software is an application used to work with PQM-701 power quality analyzer. It enables:

    • » analyzer configuration,
    • » reading data from the analyzer,
    • » network parameters check in real time,
    • » data deleting in the analyzer,
    • » data presentation in tables,
    • » data presentation in diagrams,
    • » data analysis according to EN 50160 or according to user defined conditions,
    • » independent service of multiple analyzers,
    • » software upgrade through the Internet.

    Analyzer configuration

    The software enables configuration of all analyzer’s parameters. The configuraton is made on the PC computer and later transfered to the analyzer. The configuration settings can be stored on hard drive or other data storage devices to be used later.The software enables the configuration of:

    • » wthe choice of Measurement Points and memory assigment to each Measurement Point,
    • » analyzer time settings,
    • » keyboard lock,
    • » PIN code security,
    • » averaging time setting,
    • » choice of current and voltage transformers,
    • » trigger mode choice (immidiately, after an event or according to the scheduler),
    • » choice of clamp’s type, setting of additional parameters registration in N and PE channels,
    • » choice of network type, for which the analyzer will be used.

    The analyzer has four independent Measurement Points. Each Measurement Point can be set individually to perform four different types of registration without need to change analyzer’s configuration.

    For each Measurement Point the following settings can be made:

    • » cwheather the analyzer shall work according to EN 50160 or according to user defined conditions,
    • » for each registration user can define, which network parameters shall be registered,
    • » for each parameter user can define wheather the analyzer shall register average, minimum, maximum or instantaneous values,
    • » the limits beyond which the analyzer will record the event can be defined.

    Recent data reading

    “SONEL Analysis” software enables reading of selected parameters and their graphic presentation in real time.These parameters are measured independently of the registration saved on the memory card. User can check:

    • » wvoltage and current diagrams (oscilloscope),
    • » diagrams of voltage and current in time function,
    • » scope phasor,
    • » different parameters values,
    • » harmonics and harmonics’ power.

     

    Data analysis

    With “SONEL Analysis” software user can read data stored on the memory card and analyze them. Data from the analyzer can be stored on hard drive and be used later. This feature enables data archiving.

    The user can analyze the data from the device.There is a choice of:

    • General – all data are shown with dots (Measurements, Events and Oscillograms),
    • Measurements – all measured values registered in averaging time are shown with dots (voltage, frequency, etc.),
    • Events – all detected events are shown with dots (dips, swells, interruptions, etc.).


PQM-701Zr

    Description

  • Has an independent power supply socket and an additional RS-232 interface to control a GPRS modem.
  • ANALYZER MEASURES AND RECORDS ACCORDING TO THE EN 61000 - 4-30 CLASS-A STANDARD The device is designed to work with networks with nominal frequency 50/60 Hz. The device is designed to work with networks with nominal voltage:
  • » 110/190 V,
  • » 115/200 V,
  • » 220/380 V,
  • » 230/400 V,
  • » 240/415 V,
  • » 400/690 V.

  • The network configuration is set from the computer software.
    Supported networks:
  • » single-phase,
  • » two-phase with the common N,
  • » three-phase star with and without N,
  • » three-phase triangle.
  • Specification

    Possible measurements:

      • » Measurements according to EN 50160
      • » Voltage L1, L2, L3, N-PE (five inputs, compiles with EN 61000 - 4-30, class A)
        - average, minimum, maximum and instantaneous values, range to 690 V, ability to work with voltage transformers,
      • » Current L1, L2, L3, N (four inputs)
        - average, minimum, maximum and instantaneous values, measurement current with range to 3 kA (depends on used clamp), ability to work with current transformers,
      • » Crest factor for voltage and current,
      • » Frequency from 40 Hz to 70 Hz (compiles with EN 61000 - 4-30, class A),
      • » Active, reactive, distortion, apparent power, including the type of reactive power (capacitive, inductive),
      • » Power recording:
        - Budeanu method,
        - IEEE 1459,
      • » Active, reactive, apparent energy,
      • » Power factor, cosφ, tgφ,
      • » K factor (transformer overload caused by the harmonics),
      • » Up to 50th harmonics for voltage and current (compiles with EN 61000 - 4-7, class I),
      • » Total Harmonic Distortion (THD) for voltage and current,
      • » Short-term (PST) and long-term (PLT) flicker (compiles with EN 61000 - 4-15, class A),
      • » Unballace of Voltage (compiles with EN 61000 - 4-30, class A) and current,
      • » Voltage dips, swells and interruption registration including oscillograms (compiles with EN 61000 - 4-30, class A),
      • » Current events registration including oscillograms,
      • » Current and voltage oscillograms registration after each averaging period.
      Specification Range Resolution Accuracy

      AC
      voltage
      (TRMS)

      - 0,0…690,0 V 0,01 % Un ±0,1% Un
      Crest
      Factor
      Voltage

      1,00…10,00
      (≤1,65 for
      voltage 690 V)

      0,01 ±5%
      Current 1,00…10,00
      (≤3,6 Inom)
      0,01 ± 5% m.v.
      AC
      current
      TRMS
      - depends on
      the clamp*
      0,01 % of nominal range ±0,1% of nominal
      range
      (add clamps
      accuracy)
      Frequency - 40,00...70,00 Hz 0,01 Hz ±0,01 Hz
      Active,
      reactive,
      apparent
      power
      and
      distortion
      - depends
      of configuration
      (transformers,
      clamp)
      up to 4
      decimal places
      depends
      on configuration
      (transformers,
      clamp)
      Active, reactive apparent energy - depends
      of configuration
      (transformers,
      clamp)
      up to 4
      decimal places
      the same
      as above
      cosφ
      and Power
      Factor (PF)
      - 0,00...1,00 0,01 ±0,03
      tgφ - 0,00...10,00 0,01 depends on Active
      and Reactive
      power accuracy
      Harmonics Voltage same as for AC
      voltage TRMS
      same as for
      AC voltage TRMS
      ±5% Uh
      for Uh ≥ 1% Un
      ±0,05% Un
      for Uh < 1% Un
       
      Current same as for AC
      current TRMS
      same as for
      AC current TRMS
      ± 5% Ih 
      for Ih ≥ 3% In
      ± 0,15% In
      for Ih < 3% In
      Total
      Harmonics
      Distortion
      Voltage 0,0..100,0% 0,1% ±5%
      Current ±5%
      Harmonics
      active
      and
      reactive
      power
      - depends on configuration
      (transformers,
      clamp)
      depends
      on current
      and voltage
      minimum value
      -

      Angle
      between
      voltage
      and current
      harmonics

      - -180,0…+180,0o 0,1o ±(h x 1o)
      K-Factor - 1,0...50,0 0,1 ±10%
      Flicker - 0,20...10,00 0,01 ±5%
      Unbalance Voltage and Current 0,0...20,0% 0,1% ±0,15%
      (absolute error)

      *Clamp F-1/F-2/F-3:0..3000 A (10000 Ap-p) *Clamp C-4: 0..1000 A (3600 Ap-p)*Clamp C-5: 0..1000 A (3600 Ap-p)*Clamp C-6: 0..10 A (36 Ap-p) (without current transformers)

      Sonel Analysis 1.0

      „SONEL Analysis” software is an application used to work with PQM-701 power quality analyzer. It enables:

      • » analyzer configuration,
      • » reading data from the analyzer,
      • » network parameters check in real time,
      • » data deleting in the analyzer,
      • » data presentation in tables,
      • » data presentation in diagrams,
      • » data analysis according to EN 50160 or according to user defined conditions,
      • » independent service of multiple analyzers,
      • » software upgrade through the Internet.

      Analyzer configuration

      The software enables configuration of all analyzer’s parameters. The configuraton is made on the PC computer and later transfered to the analyzer. The configuration settings can be stored on hard drive or other data storage devices to be used later.The software enables the configuration of:

      • » wthe choice of Measurement Points and memory assigment to each Measurement Point,
      • » analyzer time settings,
      • » keyboard lock,
      • » PIN code security,
      • » averaging time setting,
      • » choice of current and voltage transformers,
      • » trigger mode choice (immidiately, after an event or according to the scheduler),
      • » choice of clamp’s type, setting of additional parameters registration in N and PE channels,
      • » choice of network type, for which the analyzer will be used.

      The analyzer has four independent Measurement Points. Each Measurement Point can be set individually to perform four different types of registration without need to change analyzer’s configuration.

      For each Measurement Point the following settings can be made:

      • » cwheather the analyzer shall work according to EN 50160 or according to user defined conditions,
      • » for each registration user can define, which network parameters shall be registered,
      • » for each parameter user can define wheather the analyzer shall register average, minimum, maximum or instantaneous values,
      • » the limits beyond which the analyzer will record the event can be defined.

      Recent data reading

      “SONEL Analysis” software enables reading of selected parameters and their graphic presentation in real time.These parameters are measured independently of the registration saved on the memory card. User can check:

      • » wvoltage and current diagrams (oscilloscope),
      • » diagrams of voltage and current in time function,
      • » scope phasor,
      • » different parameters values,
      • » harmonics and harmonics’ power.

       

      Data analysis

      With “SONEL Analysis” software user can read data stored on the memory card and analyze them. Data from the analyzer can be stored on hard drive and be used later. This feature enables data archiving.

      The user can analyze the data from the device.There is a choice of:

      • General – all data are shown with dots (Measurements, Events and Oscillograms),
      • Measurements – all measured values registered in averaging time are shown with dots (voltage, frequency, etc.),
      • Events – all detected events are shown with dots (dips, swells, interruptions, etc.).



Our Clientele